This guide contains affiliate links. If you buy through them, I may earn a commission at no extra cost to you. Learn more
In this guide
To measure for a custom sauna, record the room’s width, depth, and ceiling height wall to wall, measuring each one in at least two or three places and writing down the smallest number. Then note the door and window positions, outlets, the distance to your electrical panel, and anything in the way, like posts, beams, or ducts. Add a handful of photos and you have everything a designer needs.
On construction quotes, bad measurements are the most expensive mistake I see, because they cause rework. The good news is that measuring for a sauna is easy if you’re methodical. Plan on about 30 minutes.
What you need
- A 25-foot tape measure. A metal tape is more accurate than a cloth one.
- A laser distance measurer (optional). Handy for ceilings and long walls. Basic models cost about $25 to $40 at Home Depot, Lowe’s, or Canadian Tire.
- A level (optional). A 2-foot or 4-foot level, or a level app on your phone, to check the floor.
- Your phone camera.
- Graph paper and a pencil, or the free worksheet. The free home sauna planning checklist includes a room measurement worksheet with a sketch grid.
- A helper. Not essential, but it makes long measurements easier and more accurate.
Units: in the US, measure in feet and inches (and write inches to the nearest 1/4 inch). In Canada, either imperial or metric is fine; just tell the designer which you used and stick to one.
Step-by-step measuring
Step 1: Sketch the room. Draw a rough outline of the room from above. It doesn’t need to be to scale yet. Mark which wall is which (for example, “back wall,” “door wall”), and mark north if you know it.
Step 2: Measure the width. Measure wall to wall along the back wall, at three heights: near the floor, at about waist height, and near the ceiling. Walls are rarely perfectly straight. Write down all three, then circle the smallest.
Step 3: Measure the depth. Do the same from the back wall to the front, at three points along the width. Circle the smallest.
Step 4: Measure the ceiling height. Measure floor to ceiling in at least three spots: each end and the middle. Basement floors often slope toward a drain, and ceilings sag. Use the smallest number. If there’s a beam, duct, or pipe, measure the clear height under it separately.
Step 5: Check if the room is square. Measure both diagonals, corner to corner. If they’re within about 1/2 inch of each other, the room is square enough. If they differ more, tell the designer. It affects how the panels fit.
Step 6: Mark doors and windows. For each door and window in or next to the space, record:
- Width and height
- Distance from the nearest corner
- Height of the window sill from the floor
- Which way the door swings
Step 7: Mark obstacles. Measure and mark anything that will affect the sauna:
- Support posts (size and distance from two walls)
- Beams, ducts, or soffits (size, height, and position)
- Sloped ceilings (height at the low side and the high side, and where the slope starts)
- Baseboard heaters, radiators, or HVAC vents
- Floor drains or sump pumps
Step 8: Mark power. Note existing outlets (and whether any are on a 20-amp circuit if you know), light switches, and where the electrical panel is. Estimate the cable path from the panel to the sauna spot, in feet. See the electrical requirements guide.
Step 9: Check the floor. Lay a level in a few spots. Note if the floor slopes and by about how much. Note the floor type (concrete, tile, vinyl, wood, carpet).
Step 10: Measure the delivery path. This is the step most people skip. Measure:
- Width of every door the sauna parts will pass through
- Width of hallways
- Stair width and headroom, if it’s going to a basement or upstairs
- Any tight turns
The longest sauna panels can be 7 feet or more. If they can’t get to the room, nothing else matters.
Photos to take
Photos let a designer spot problems that numbers miss. Take these, in good light:
- Each wall straight on, from the opposite side of the room (4 photos).
- Each corner where the sauna will sit, showing floor and ceiling.
- The ceiling, showing any beams, ducts, sprinklers, or lights.
- The floor, including any drain.
- Every obstacle, with the tape measure visible in the shot.
- The electrical panel with the door open (the breaker labels), plus a wide shot showing where it is.
- Existing outlets near the sauna spot.
- The delivery path, including stairs and doorways.
- The view through any window the sauna will face, if you want to plan glass around it.
Tip: hold the tape measure across features in the photo. A picture of a post with the tape showing “37 1/2 inches to the wall” is worth more than a note.
Common measuring mistakes
These are the mistakes I see most on renovation jobs, and they apply to saunas too:
Measuring once. Walls and ceilings aren’t perfectly straight. One measurement can be off by an inch. Always measure in multiple places and use the smallest.
Measuring over baseboards and trim. Measure wall to wall, above the baseboard. Then note the baseboard’s thickness separately. Designers need to know what’s in the way at floor level.
Forgetting the low point. In basements, the lowest point is often a duct or beam you stopped noticing years ago. Measure clear height under everything.
Mixing units. Writing some numbers in inches and some in feet and inches leads to errors. Use inches for everything (for example, “84 inches,” not “7 feet”).
Ignoring the door swing. A door that opens into the sauna space takes up floor area. Note which way every nearby door opens.
Not planning clearance. Prefab saunas need a gap from walls and ceiling for air. Custom saunas are built differently, but still need room for wiring and assembly. Ask the designer what gap to plan for.
Forgetting the delivery path. I’ll say it again: measure the stairs and doors.
Rounding up. If a wall is 83 3/4 inches, write 83 3/4, not 84. A quarter inch too big means the sauna won’t fit. A quarter inch too small just means a slightly larger trim gap.
What size do you need?
Once you know your space, here’s a rough guide to what fits:
| Use | Minimum inside space (approx.) |
|---|---|
| 1 person sitting | 4 × 4 feet |
| 2 people sitting | 5 × 5 feet |
| 1 person lying down | About 6 1/2 feet of bench length |
| 2 to 3 people, L-shaped bench | About 6 × 4 feet |
| Two-tier benches | About 6 × 6 feet and an 8-foot ceiling |
The first two rows come from SaunaCloud’s guidance, which also recommends a ceiling of 7 to 8 feet. SaunaCloud’s sample custom floor plans range from a compact 38 × 42-inch room with one bench to a 69 × 79-inch two-tier layout, with benches 22 inches deep. These are measured wall to wall, before the wood interior goes in.
A sample measurement sheet
Here’s what a finished set of notes might look like for a basement corner. Copy the format for your own room:
- Width (back wall): 70 1/4 in (floor), 70 in (middle), 69 3/4 in (top). Use 69 3/4 in.
- Depth (side wall): 49 1/2 in, 49 1/4 in, 49 1/2 in. Use 49 1/4 in.
- Ceiling height: 91 in, 90 1/2 in, 91 in. Duct at front edge: 84 in clear.
- Diagonals: 85 3/4 in and 86 in. Square enough.
- Door: existing room door 32 in wide, opens into the hallway, not the space.
- Obstacles: 4 × 4 in post, 12 in from the side wall and 38 in from the back wall.
- Power: panel on the opposite wall, about 22 ft cable run along open joists.
- Floor: sealed concrete, slopes about 1/4 in toward the drain.
- Delivery: stairs 36 in wide, 78 in headroom at the bottom.
A note like this, plus photos, gives a designer almost everything they need for an accurate first proposal.
Send your measurements for a design
Once you have your measurements and photos, you’re ready for a design.
With SaunaCloud, you can start with just a rough size: width, depth, ceiling height, where you’d like the door and any windows, and whether you prefer to sit or lie down. The designer sends 3D renderings and a written proposal in 24 to 48 hours. You can then review it on a free 30-minute call, or by email. There’s no obligation, and you can refine the design before you commit.
Exact measurements matter more once you’re ready to order, because custom saunas are built to your numbers and usually can’t be returned. Use the rough numbers to get your design, then re-measure carefully before you sign.
Frequently asked questions
What measurements do I need for a custom sauna? Width, depth, and ceiling height (wall to wall), the positions of doors and windows, any obstacles like posts or beams, and the location of your electrical panel.
Should I measure from the drywall or the studs? Measure from the finished wall surface (usually drywall) unless the designer asks for stud-to-stud measurements. If the walls aren’t finished yet, say so and measure stud to stud.
How accurate do sauna measurements need to be? To the nearest 1/4 inch for the final order. For a first design, rough measurements are fine.
What’s the minimum size for a home sauna? About 4 × 4 feet inside for 1 person and 5 × 5 feet for 2, with a ceiling of 7 to 8 feet.
Do I need to measure the doorways to the room? Yes. Sauna panels and wood bundles need a clear path. Measure every door, hallway, and staircase they’ll pass through.
Can I measure in metric? Yes. Just tell the designer which units you used and keep everything in one system.